It sounds like its trying to pair with some generic deivce and has interupted the driver in order to do so. Its saying the driver has been interupted to allow some other device. Please repair duel shock to continue or disregard" "PS3 driver temporarily interupted in order to allow compatibility with standard BT periferals. I dont think that message is saying its blocking pairing with other devices. The first time I did this - when I managed to get it to pair, I dont think I got that message. I then went back to the ps3 driver and at the end got that "driver disabled message". Im fairly sure this is what happened last time I tried the sixaxis driver. Exit to the main RetroPie-Setup menu, then reboot.Īfter restart, EmulationStation will prompt you to setup a controller - if the pairing worked and after the reboot the wireless connection is re-established, you can try to configure the Bluetooth connected controller.ĭid a fresh install again and tried the sixaxis - everything seemed to go ok, didnt get the "driver disabled message" - however the pad wont pair at all this time. If pairing works - then go back to the main RetroPie-Setup menu, go to Configuration/Tools, then emulationstation and choose to clear/reset the controller configuration. Remove any Bluetooth connected devices from the Bluetooth menu before pairing. My advice would be to remove the ps3controller and try only with the sixaxis driver, configured for 3rd party controllers. Because the ps3controller driver block the pairing with other Bluetooth devices, the driver is stopped during Bluetooth pairing. The message about the PS3 driver appears when you have the ps3controller driver installed and it's ok. I see, I thought you've reset the controllers before re-doing the pairing. The very first time I started after a os install it prompted and i setup the controller with usb. Pressed ok,went back to menu - removed cable - nothing said in Problem connecting a bluetooth ps3 controller: Please repair duel shock to continue or disregard. Now I get a message saying "PS3 driver temporarily interupted in order to allow compatibility with standard BT periferals. I removed the registered BT device and re-registered this time choosing the first device option (that was all mac adress looking, not the one that said ps3 controller). On reboot the controller works fine with cable but nothing if I remove it. Pulled the power cable to reboot with controller attached via cable. Turned it back on, all lights flashed for a moment and then 1 steady on.Ĭonnected the usb cable - still noting works I help teh PS button down - nothing until it turned off. I removed the usb cable - nothing works although now the ctrl leds arnt all flashing, theres just one steady on which I assume means it connected. Got a message saying successful authentication, you can now remove the usb cable (never seen this before). The second option was a mac like address followed by "playstation controller" This time I was given an option of 2 devices (never had that before) One was just numbers and letters like a mac addres. With the cable connected I checked for paired BT devices - none found Installed clone support gasia (fairly sure my controller is gasia, saw it a few times in messages while iv been messing about). I then uninstalled sixaxis and installed ps3controller With cable still attached I then went to bluetooth - register deviceĭisconnected teh cable, pressed the ps button and re-connected the cable Oookay.on a fresh OS install, with the PS3 controller attached via usb I setup the controller I removed the bluetooth device and tried to start from scratch and now it wont even connect teh device :( Through multiple removing and reconnecting I saw a message saying "duel shock, disconnect controller press ps button then reconnect" - so I attached the usb and did this and I then went to configure the controller which went fine and it worked - with teh usb cable attached. I read on another thread that I dont need to bothere with that bit and so long as the device is registered I can just config the controller which doesnt seem to be the case. During the "register and connect" I have connected the device and I then go to a section about security and any option I choose just seems to do nothing but freeze. USB devices - wifi dongle for a keyboard - Dragon Shock 3rd party PS3 controller (bluetooth).īut Im still having trouble.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |